Integration, implementation and testing of the X-Band SASAR II system

 

Show simple item record

dc.contributor.advisor Inggs, Michael en_ZA
dc.contributor.author George, Georgie en_ZA
dc.date.accessioned 2014-07-31T10:57:43Z
dc.date.available 2014-07-31T10:57:43Z
dc.date.issued 2007 en_ZA
dc.identifier.citation George, G. 2007. Integration, implementation and testing of the X-Band SASAR II system. University of Cape Town. en_ZA
dc.identifier.uri http://hdl.handle.net/11427/5217
dc.description Includes abstract.
dc.description Includes bibliographical references (leaves 122-123).
dc.description.abstract This dissertation focuses on the integration, implementation and testing of the X-Band (9.3 GHz) South African Synthetic Aperture Radar project (SASAR II). The SASAR II system was divided into three main subsystems for design and implementation at M.Sc. level. The three main systems were the transmitter and frequency distribution unit (FDU), the receiver and the radar digital unit (RDU). Although all subsystems are separate units, the design process was a collaborative effort. The purpose of a synthetic aperture radar (SAR) is to provide high resolution images of extensive areas from airborne platforms operating from long ranges. The SASAR II project was born out of the success of its predecessor, SASAR, which was a VHF SAR commissioned in 2000. The SASAR II system is a wide bandwidth X-Band radar system with a high resolution of 2x2m. The processed resolution of the SASAR II system is enhanced through design improvements of the transmitted bandwidth, pulse coding and the overall system coherency. The purpose of this dissertation is to verify the original design specifications of the system and to test its integrity when all subsystems are combined. The critical parameters for monitoring and testing are the power budget levels for each RF unit. An insufficient input drive for a mixer may result in a null output. Conversely a high input drive will result in the saturation of the device and the generation of intermodulation products and higher conversion losses. Testing of the digital pulse generator (DPG), which is part of the RDU, showed a drop in the specified output power of 10 dB. The power budget calculations made for the transmitter were made based on the input power of the DPG. The DPG unit also failed to provide adequate port to port isolation between the input trigger and the I & Q output channels. Spurious harmonics signals from the trigger resulted in aliasing with the IF frequencies. An extra filtering stage was added at the front end to isolate these harmonics. The sensitivity time control (STC) and the manual gain control (MGC) form the final amplification/attenuation stages of the receiver unit. The combination of the two units results in final output signal amplitudes of between 2.15 dBm and 32.5 dBm. The specified maximum input power of the ADC is 10 dBm. The additional gain stages in the MGC would drive the ADC into saturation and possibly result in permanent damage. The testing of the receiver and the ADC was therefore limited to low power testing. The complete system response closely matched that of the design specification. The sources of the spurious signals described in the previous dissertations were isolated and filtered out. This however required the use of pulsed RF measurement techniques, specifically regarding the use of the pulse desensitization factor (PDF). Since the tested signals have a PRF, the measurement equipment takes an average of the peak pulse power distributed over all the spectral components over a given PRI. The PDF therefore compensates for the drop in signal power. en_ZA
dc.language.iso eng en_ZA
dc.subject.other Electrical Engineering en_ZA
dc.title Integration, implementation and testing of the X-Band SASAR II system en_ZA
dc.type Thesis / Dissertation en_ZA
uct.type.publication Research en_ZA
uct.type.resource Thesis en_ZA
dc.publisher.institution University of Cape Town
dc.publisher.faculty Faculty of Engineering & the Built Environment en_ZA
dc.publisher.department Department of Electrical Engineering en_ZA
dc.type.qualificationlevel Masters en_ZA
dc.type.qualificationname MSc en_ZA
uct.type.filetype Text
uct.type.filetype Image


Files in this item

This item appears in the following Collection(s)

Show simple item record